BOSS Audio Systems BAB8 Amplified Car Subwoofer – 800 Watts Max Power, Low Profile, 8 Inch Subwoofer, Remote Subwoofer Control, Great for Vehicles That Need Bass But Have Limited Space
Space Saver – The combination of amplifier and subwoofer all into one, makes this ideal for spatially challenged vehicles. With a slim design, there are a few installation options. Embrace the Bass.
Built-in Amplifier – A built-in 800 Max watt amplifier powers the subwoofer
Pulse Width Modulated – This design controls the output voltage and current precisely by not only removing the output current sensing loss, but also eliminating all secondary feedback circuitry. It increases efficiency, is lighter, smaller reliable
Variable Low-Pass Filter – A low-pass filter is an electronic circuit that removes all the notes below the filter’s frequency setting. You will use the Low-pass filter to primarily keep high notes out of your subwoofer(s)
High Level Input – Speaker level inputs are commonly referred to as high-level inputs. It will be used to connect the BAB8 to your factory radio or an aftermarket radio that does not have low-level (RCA) inputs
Low Level Input – Line level inputs, also known as RCA inputs or low-level inputs, use RCA interconnect cables to link the BAB8 with the source unit. Most aftermarket radios have multiple pairs of RCA outputs that can connect to multiple amplifiers
Variable Bass Boost – Variable Bass Boost allows you to adjust the low bass within the boost range to just the way you like it.
Break Your Subwoofer In
Much like the engine of a new automobile, a new subwoofer must go through a short but important process of “break-in” before it is run under harsh conditions. The “break-in” process will ensure the subwoofer is able to perform as it has been designed to. This process involves subjecting the subwoofer to no more than low-to-medium volume levels for a number of hours in the enclosure. 3-4 hours is generally sufficient for the subwoofer’s suspension to loosen enough to prevent the voice coil(s) from overheating and causing failure. The break-in period is also effective in extending subwoofer life. Over-driving the woofer before it has been properly broken-in will usually result in premature failure and poor performance.
8-inch 800-Watt subwoofer
Class A/B built-in amplifier
MOSFET power supply
RCA & speaker level input
Phase control
Bass boost
Low pass filter
Remote subwoofer control
Amplified Space Saver
A built-in amplifier powers the 8-inch subwoofer. No need to have a subwoofer housed in a box AND a separate amplifier. If you have a small cabin to work with, the BAB8 will provide the rich bass that every sound system cannot do without.
Remote Subwoofer Control
A wired remote subwoofer control at your fingertips gives you control, so when the need hits… so does your BASS
Reviews
There are no reviews yet.
Be the first to review “BOSS Audio Systems BAB8 Amplified Car Subwoofer” Cancel reply
BOSS Audio Systems BAB8 Amplified Car Subwoofer - 800 Watts Max Power, Low Profile, 8 Inch Subwoofer, Remote Subwoofer Control, Great for Vehicles That Need Bass But Have Limited Space
Boss Audio System Phantom - 12" DUAL Voice Coil (4 Ohm) 2600W Subwoofer. (Sold Single) P129DC
Phantom 6.5" 2-Way 500W Component Speakers. (Sold in Pairs)
BOSS Audio Systems R94 Car Speakers 500 Watt Per Pair, 6 x 9 Inch, Full Range, 4 Way Sold in Pairs
BlackDeath 6 Inch Pro Audio Midrange
High Output 6″ Pro Audio
Driver Alloy Gasket included
Sold in Singles
The new range of Vibe Slick speakers are the most efficient Vibe speaker to date.
Content
BOSS Audio Systems BAB8 Amplified Car Subwoofer
Space Saver - The combination of amplifier and subwoofer all into one, makes this ideal for spatially challenged vehicles. With a slim design, there are a few installation options. Embrace the Bass.
Built-in Amplifier - A built-in 800 Max watt amplifier powers the subwoofer
Pulse Width Modulated - This design controls the output voltage and current precisely by not only removing the output current sensing loss, but also eliminating all secondary feedback circuitry. It increases efficiency, is lighter, smaller reliable
Variable Low-Pass Filter - A low-pass filter is an electronic circuit that removes all the notes below the filter's frequency setting. You will use the Low-pass filter to primarily keep high notes out of your subwoofer(s)
High Level Input - Speaker level inputs are commonly referred to as high-level inputs. It will be used to connect the BAB8 to your factory radio or an aftermarket radio that does not have low-level (RCA) inputs
Low Level Input - Line level inputs, also known as RCA inputs or low-level inputs, use RCA interconnect cables to link the BAB8 with the source unit. Most aftermarket radios have multiple pairs of RCA outputs that can connect to multiple amplifiers
Variable Bass Boost - Variable Bass Boost allows you to adjust the low bass within the boost range to just the way you like it.
Break Your Subwoofer In
Much like the engine of a new automobile, a new subwoofer must go through a short but important process of “break-in” before it is run under harsh conditions. The “break-in” process will ensure the subwoofer is able to perform as it has been designed to. This process involves subjecting the subwoofer to no more than low-to-medium volume levels for a number of hours in the enclosure. 3-4 hours is generally sufficient for the subwoofer’s suspension to loosen enough to prevent the voice coil(s) from overheating and causing failure. The break-in period is also effective in extending subwoofer life. Over-driving the woofer before it has been properly broken-in will usually result in premature failure and poor performance.
8-inch 800-Watt subwoofer
Class A/B built-in amplifier
MOSFET power supply
RCA & speaker level input
Phase control
Bass boost
Low pass filter
Remote subwoofer control
Amplified Space Saver
A built-in amplifier powers the 8-inch subwoofer. No need to have a subwoofer housed in a box AND a separate amplifier. If you have a small cabin to work with, the BAB8 will provide the rich bass that every sound system cannot do without.
Remote Subwoofer Control
A wired remote subwoofer control at your fingertips gives you control, so when the need hits… so does your BASS
One 12" Woofer with DUAL 4 ohm Voice Coil
2600 Watts MAX 1300 Watts RMS Power Handling
88dB Sensitivity, 28 Hz Resonant Frequency
Polypropylene & Paper Cone and Rubber Surround
Works in .65 CuFt Sealed or 1.5 CuFt Ported enclosure
Component 6.5" 2-Way Speaker Pair
500 Watts MAX 250 Watts RMS Power Handling per Pair
65 Hz to 20 kHz Frequency Response and 94dB Sensitivity
Electroplate Injection Woofer Cone and Rubber Surround
1 Tweeter Per Speaker
Sold in Pairs
BOSS Audio Systems R94 Car Speakers 500 Watt Per Pair, 6 x 9 Inch, Full Range, 4 Way Sold in Pairs
Full Range 6" x 9" 4-Way Car Speakers Pair
500 Watts MAX 250 Watts RMS Power Handling per Pair
50 Hz to 20 kHz Frequency Response and 92dB Sensitivity
Poly Injection Woofer Cone and Rubber Surround
2 Tweeters and 2.5 inch Mylar Dome Midrange Per Car Speakers
Sold in Pairs
Before making your purchase, find out what type of speakers you will be replacing. You can simply measure the existing speakers and go from there. If you do not have any to begin with, a local Audio/Video shop can guide you with a few simple questions about your vehicle. Most of the time you will be able to drop them right in with little to no alterations needed. Pay close attention to the RMS power handling of the speakers you are purchasing. This is the continuous power that a speaker can handle without distorting. Your head unit will have to have the proper number of speaker outputs compared to how many speakers you plan to hook up to it, as well as sufficient power from the built-in amplifier. Sometimes though, a separate or external amplifier will have to be employed so that your speakers get the adequate power they need for optimal performance.
Full Range, 4-Way, 6” x 9”
Dimensions: Length 9.5” Width x 6.8” x Height 3.3”
Impedance: 4 Ohms, Frequency Response: 50Hz – 20KHz
Sensitivity: 92 dB @ 1 W/1 m
Cone: Poly Injection, Midrange: 2.5” Mylar Dome
Surround: Rubber, Basket: Stamped, Tweeter: 1” Dome & 0.5” Piezo
Poly Injection Cone
Polypropylene is a resilient and durable manufactured material. It allows for maximum flexibility that produces great sounding speakers.
Rubber Surround
Impermeable to air, rubber has the ability to endure or resist exposure to the many types of weather fronts. Rubber has many different applications. We use it for the surrounds in a many of our speakers to connect the cone to the basket
Dome Tweeter
Dome tweeters have improved sound dispersion and the shape radiates sound with a wider dispersion pattern than the semi-dome design. Since high-frequency sound waves are very directional, a wider dispersion of the sound waves will give you a larger "sweet spot" to work with when setting up your system
Piezoelectric Tweeter
Piezoelectric tweeters are resistant to overloads that would normally destroy most high frequency drivers and they can be used without a crossover due to their electrical properties. The active element is basically a piece of polarized material (i.e. some parts of the molecule are positively charged, while other parts of the molecule are negatively charged)
Competition 6" pro audio speaker
The BDPRO6M-V9: BlackDeath 6 Inch Pro Audio Midrange component woofer is designed with excellent mid-bass response in mind. Semi-pressed paper cone has high sensitivity and low moving mass for monstrous output Dual roll cloth surround offers fast, precise dampening of the cone with great bass response. The BlackHole Dustcap increases effective cone area for higher SPL creating extreme volume.
Blackdeath range
VIBE Audio’s BlackDeath range is all about taking things to the extreme and creating products so crazy they have no right to exist. BlackDeath isn’t just about pushing the boundaries of audio innovation, it’s about annihilating them.
For many years people have been asking for coaxial and component speakers that are worthy to wear the BlackDeath logo, and after extensive development Vibe are proud to release the BlackDeath Pro Audio range. Derived from PA speaker design, BlackDeath Pro Audio speakers are capable of immense sound pressure levels, meaning volume like you’ve never heard before. Ideal for competition use or for those who just want to play their music loud and proud.
Specifications
Model : BlackDeath Pro 6M
Configuration : 1 Way
Speaker Size : 6″ (170mm)
RMS Power : 175 watts
Peak Power : 525 watts
Minimum Input : 75 watts
Sensitivity : 97 dB
Freq. Response : 75 Hz – 10 kHz
Impedance : 4 Ohm
Mounting Depth : 2.7″ (68mm)
Mounting Diameter: 5.7″ (146mm)
Voice Coil Diameter : 2″ (38mm)
Magnet Weight : 34 oz
Torsion basket featuring snap on mounting tabs for greater installation flexibility.
Sold as single speaker
British Engineered 1 Inch Component Tweeter
The secret weapon is the incredible tweeter. The component tweeter uses high end components and is one of the smallest on the market, but packs a huge punch, causing Car & Hifi magazine to call it a force to be reckoned with as it provides great detail and good spatiality.
Reviews
There are no reviews yet.