BOSS Audio Systems BAB8 Amplified Car Subwoofer – 800 Watts Max Power, Low Profile, 8 Inch Subwoofer, Remote Subwoofer Control, Great for Vehicles That Need Bass But Have Limited Space
Space Saver – The combination of amplifier and subwoofer all into one, makes this ideal for spatially challenged vehicles. With a slim design, there are a few installation options. Embrace the Bass.
Built-in Amplifier – A built-in 800 Max watt amplifier powers the subwoofer
Pulse Width Modulated – This design controls the output voltage and current precisely by not only removing the output current sensing loss, but also eliminating all secondary feedback circuitry. It increases efficiency, is lighter, smaller reliable
Variable Low-Pass Filter – A low-pass filter is an electronic circuit that removes all the notes below the filter’s frequency setting. You will use the Low-pass filter to primarily keep high notes out of your subwoofer(s)
High Level Input – Speaker level inputs are commonly referred to as high-level inputs. It will be used to connect the BAB8 to your factory radio or an aftermarket radio that does not have low-level (RCA) inputs
Low Level Input – Line level inputs, also known as RCA inputs or low-level inputs, use RCA interconnect cables to link the BAB8 with the source unit. Most aftermarket radios have multiple pairs of RCA outputs that can connect to multiple amplifiers
Variable Bass Boost – Variable Bass Boost allows you to adjust the low bass within the boost range to just the way you like it.
Break Your Subwoofer In
Much like the engine of a new automobile, a new subwoofer must go through a short but important process of “break-in” before it is run under harsh conditions. The “break-in” process will ensure the subwoofer is able to perform as it has been designed to. This process involves subjecting the subwoofer to no more than low-to-medium volume levels for a number of hours in the enclosure. 3-4 hours is generally sufficient for the subwoofer’s suspension to loosen enough to prevent the voice coil(s) from overheating and causing failure. The break-in period is also effective in extending subwoofer life. Over-driving the woofer before it has been properly broken-in will usually result in premature failure and poor performance.
8-inch 800-Watt subwoofer
Class A/B built-in amplifier
MOSFET power supply
RCA & speaker level input
Phase control
Bass boost
Low pass filter
Remote subwoofer control
Amplified Space Saver
A built-in amplifier powers the 8-inch subwoofer. No need to have a subwoofer housed in a box AND a separate amplifier. If you have a small cabin to work with, the BAB8 will provide the rich bass that every sound system cannot do without.
Remote Subwoofer Control
A wired remote subwoofer control at your fingertips gives you control, so when the need hits… so does your BASS
Reviews
There are no reviews yet.
Be the first to review “BOSS Audio Systems BAB8 Amplified Car Subwoofer” Cancel reply
BOSS Audio Systems BAB8 Amplified Car Subwoofer - 800 Watts Max Power, Low Profile, 8 Inch Subwoofer, Remote Subwoofer Control, Great for Vehicles That Need Bass But Have Limited Space
BlackDeath 6 Inch Pro Audio Midrange
High Output 6″ Pro Audio
Driver Alloy Gasket included
Sold in Singles
Chaos Exxtreme 6" x 9" 2-Way 350W Full Range Speakers. (Sold in Pairs)
PULSE4-V0: Pulse 4 Inch Coaxial Speaker
Easy upgrade
Complete with grills
Chaos Exxtreme 6" x 9" 3-Way 400W Full Range Speakers. (Sold in Pairs)
Double-DIN, DVD Player 6.2" Touchscreen Bluetooth
Content
BOSS Audio Systems BAB8 Amplified Car Subwoofer
Space Saver - The combination of amplifier and subwoofer all into one, makes this ideal for spatially challenged vehicles. With a slim design, there are a few installation options. Embrace the Bass.
Built-in Amplifier - A built-in 800 Max watt amplifier powers the subwoofer
Pulse Width Modulated - This design controls the output voltage and current precisely by not only removing the output current sensing loss, but also eliminating all secondary feedback circuitry. It increases efficiency, is lighter, smaller reliable
Variable Low-Pass Filter - A low-pass filter is an electronic circuit that removes all the notes below the filter's frequency setting. You will use the Low-pass filter to primarily keep high notes out of your subwoofer(s)
High Level Input - Speaker level inputs are commonly referred to as high-level inputs. It will be used to connect the BAB8 to your factory radio or an aftermarket radio that does not have low-level (RCA) inputs
Low Level Input - Line level inputs, also known as RCA inputs or low-level inputs, use RCA interconnect cables to link the BAB8 with the source unit. Most aftermarket radios have multiple pairs of RCA outputs that can connect to multiple amplifiers
Variable Bass Boost - Variable Bass Boost allows you to adjust the low bass within the boost range to just the way you like it.
Break Your Subwoofer In
Much like the engine of a new automobile, a new subwoofer must go through a short but important process of “break-in” before it is run under harsh conditions. The “break-in” process will ensure the subwoofer is able to perform as it has been designed to. This process involves subjecting the subwoofer to no more than low-to-medium volume levels for a number of hours in the enclosure. 3-4 hours is generally sufficient for the subwoofer’s suspension to loosen enough to prevent the voice coil(s) from overheating and causing failure. The break-in period is also effective in extending subwoofer life. Over-driving the woofer before it has been properly broken-in will usually result in premature failure and poor performance.
8-inch 800-Watt subwoofer
Class A/B built-in amplifier
MOSFET power supply
RCA & speaker level input
Phase control
Bass boost
Low pass filter
Remote subwoofer control
Amplified Space Saver
A built-in amplifier powers the 8-inch subwoofer. No need to have a subwoofer housed in a box AND a separate amplifier. If you have a small cabin to work with, the BAB8 will provide the rich bass that every sound system cannot do without.
Remote Subwoofer Control
A wired remote subwoofer control at your fingertips gives you control, so when the need hits… so does your BASS
Competition 6" pro audio speaker
The BDPRO6M-V9: BlackDeath 6 Inch Pro Audio Midrange component woofer is designed with excellent mid-bass response in mind. Semi-pressed paper cone has high sensitivity and low moving mass for monstrous output Dual roll cloth surround offers fast, precise dampening of the cone with great bass response. The BlackHole Dustcap increases effective cone area for higher SPL creating extreme volume.
Blackdeath range
VIBE Audio’s BlackDeath range is all about taking things to the extreme and creating products so crazy they have no right to exist. BlackDeath isn’t just about pushing the boundaries of audio innovation, it’s about annihilating them.
For many years people have been asking for coaxial and component speakers that are worthy to wear the BlackDeath logo, and after extensive development Vibe are proud to release the BlackDeath Pro Audio range. Derived from PA speaker design, BlackDeath Pro Audio speakers are capable of immense sound pressure levels, meaning volume like you’ve never heard before. Ideal for competition use or for those who just want to play their music loud and proud.
Specifications
Model : BlackDeath Pro 6M
Configuration : 1 Way
Speaker Size : 6″ (170mm)
RMS Power : 175 watts
Peak Power : 525 watts
Minimum Input : 75 watts
Sensitivity : 97 dB
Freq. Response : 75 Hz – 10 kHz
Impedance : 4 Ohm
Mounting Depth : 2.7″ (68mm)
Mounting Diameter: 5.7″ (146mm)
Voice Coil Diameter : 2″ (38mm)
Magnet Weight : 34 oz
Torsion basket featuring snap on mounting tabs for greater installation flexibility.
Sold as single speaker
Full Range 6" x 9" 2-Way Speaker Pair
350 Watts MAX 175 Watts RMS Power Handling per Pair
50 Hz to 20 kHz Frequency Response and 92dB Sensitivity
Poly Injection Woofer Cone and Rubber Surround
1 Tweeter Per Speaker
Sold in Pairs
Entry level 4 inch Coaxial speaker with IMPP Cone
The PULSE4-V0: Pulse 4 Inch Coaxial Speaker are the new entry level range from Vibe. Designed to be extremely efficient to produce the best response possible without the need for an amplifier upgrade.
Specifications
4”(100mm) 2-way high efficiency coaxial speaker 120 Watt
Peak Power output – 40 Watts
RMS Frequency Response: 100HZ – 20KHZ
Sensitivity 83dB
Mounting Diameter 3.7” (95MM)
Mounting Depth 1.7” (44MM)
Impedance : 4 OHMS
Spade Terminal allows easy connection of speaker Cable.
PEI Tweeter – PEI dome tweeters deliver extended high frequency response.
Torsion basket featuring snap on mounting tabs for greater installation flexibility.
IMPP Woofer Cone – Rigid injection moulded polypropylene (IMPP) woofer cone delivers smooth, low bass and great vocal reproduction.
Full Range 6" x 9" 3-Way Speaker Pair
400 Watts MAX 200 Watts RMS Power Handling per Pair
50 Hz to 20 kHz Frequency Response and 92dB Sensitivity
Poly Injection Woofer Cone and Rubber Surround
1 Tweeter and 2 inch Polyimide Cone Midrange Per Speaker
Sold in Pairs
80 Watts x 4 Max Power, RBDS Tuner, Balance/Fader/Bass/Treble and Preset built-in EQ
Plays Bluetooth/DVD/CD/USB/SD, VCD, WMA, JPEG, FM/AM, Digital Media from Smart Phones
Compatible with Audio out from Smart Phones and MP3 Players
USB, SD, Aux, AV, Rear Camera, Steering Wheel Control Input
Video, Front, Rear & Sub Pre Amp Outputs
Wireless Remote, USB Charging
Bluetooth Hands Free, Make and receive calls, Bluetooth Audio Streaming. Play and control music and apps like Spotify/Pandora wirelessly
Reviews
There are no reviews yet.