Category: Brand:


د.إ 1,044.75

The BX8 D3 from M-Audio is a 2-way, 150W powered studio monitor designed to offer a wide frequency response and easy configuration for mixers, DJs, producers, and recordists in small to medium control rooms, personal studios, and mobile rigs. The monitor produces a frequency response of 37 Hz to 22 kHz, thanks to two Class A/B amplifiers feeding an 8″ Kevlar woofer and a 1.25″ silk dome tweeter.

A rear-mounted bass port delivers extended bass response, while the tweeter’s custom waveguide yields a wide sweet spot and minimized high-frequency scatter. Volume and low-frequency controls are provided so you can tune the monitor to cooperate with the sound of the room. Place the monitor on the supplied acoustic foam pad to decouple it from your table or stands, which aids in reducing unwanted bass vibrations.

The BX8 D3 can interface with a variety of equipment, via balanced XLR and balanced/unbalanced 1/4″ TRS input jacks. Setup is simple, due to the front-mounted LED, which appears brighter when you are at the ideal angle.

A magnetically shielded 8″ military-grade Kevlar woofer provides durability and detailed transient response whilst negating unwanted “cone breakup.” It has a high-temperature voice coil and damped rubber surround. The magnetically shielded 1.25″ silk dome tweeter delivers high frequencies up to 22 kHz with minimal resonance.

The rear-mounted bass port yields extended bass response while reducing audible air turbulence that can occur at high sound pressure levels. The tweeter sits in a custom waveguide designed to lessen scatter and yield a wide sweet spot. The process of aligning the monitor’s position is simplified, due to the front-mounted LED, which shines brightly when you’re located at the ideal angle.

The BX8 D3 has two Class A/B amplifiers, an 80W low-frequency amp and a 70W high-frequency amp. A crossover at 2 kHz ensures that the correct frequencies are fed to each driver.

In addition to adjustable volume, there is a low-frequency “Acoustic Space” control. Based upon the sound of your room, you may wish to tweak the bass response to achieve a certain frequency balance.

The BX8 D3 can accept a balanced line-level input at its XLR 3-pin connector. Route balanced or unbalanced signals into the monitor via the 1/4″ TRS jack.

Share it:
Title Value
Brand M-audio
Height N/A
width N/A
inputs No
outputs No
Depth N/A
Crossover Freq 2 kHz
Input Impedance 10 kOhms (balanced) 20 kOhms (unbalanced)
Input sensitivity -12 dBU
Amplifier Power N/A
Polarity Positive signal at “Plus” input produces outward low-frequency cone displacement
Equalizer N/A
Frequency Response 37 Hz to 22 kHz
Protection RF interference Output current limiting Over temperature Turn on/off transient Subsonic filter External mains fuse
Dimensions 9.8 x 11.9 x 15.1″ / 250 x 302 x 384 mm
Cabinet Vinyl-laminated, high-acoustic-efficiency MDF
Type 2-way
Low-Frequency Driver N/A
Frequency Response (-6 dB) 37 Hz to 22 kHz
High-Frequency Driver N/A
Crossover Frequency 2 kHz
Signal to Noise Ratio (SNR) N/A
Input Connectors 1 x XLR 3-pin (balanced) 1 x 1/4″ TRS (balanced/unbalanced)
Dynamic Power N/A
Indicators N/A
Power Requirements 100 to 120 V, 50/60 Hz 220 to 240 V, 50/60 Hz/td>
Consumption 150 W
Magnetically Shielded Yes
Amplifier Class A/B
Drivers 1 x 8″ / 203 mm Kevlar woofer 1 x 1.25″ / 32 mm silk dome tweeter
Maximum Sound Pressure No
Controls and Indicators No
Controls No
Fuse 100 to 120 V ~ T2AL 250 V 220 to 240 V ~ T1AL 250 V
Connectors No
LF Roll Off No
Equalizer Control Bands No


Be the first to review “BX8 D3(EACH)”


Custom Tab Content here.
Tail sed sausage magna quis commodo snasae. Aliquip strip steak esse ex in ham hock fugiat in. Labore velit pork belly eiusmod ut shank doner capicola consectetur landjaeger fugiat excepteur short loin. Pork belly laboris mollit in leberkas qui. Pariatur snasae aliqua pork chop venison veniam. Venison sed cow short loin bresaola shoulder cupidatat capicola drumstick dolore magna shankle.